Expert Answers about Ram ProMaster City
- Which Side of MORryde RV Cargo Sliding Tray # MR97FR Slides
- The narrow portion of the MORryde RV Cargo Sliding Tray # MR97FR is the sliding portion. So basically if you were to pull it out in front of you the width is 48 inches and the depth is 26 inches.
view full answer... - Can 12V Power Wire of Tekonsha T-One be Connected to 12V Outlet on a 2015 Ram ProMaster City
- That is a great question that a lot of people have been wondering about. The purpose of the black 12V wire that comes with the Tekonsha T-One # 118719 is to bypass drawing power off of your OEM wiring. If you were to tie it into the 12V accessory outlet at the rear of your 2015 Ram ProMaster City then it could possibly overdraw that circuit.
To ensure that everything works properly and that you don't damage any OEM wiring on your vehicle I highly recommend running the power wire to your...
view full answer... - Installation of Ventline Vanair # VP-543SP onto a 2017 Ram ProMaster City cargo van
- Typically, folks will use pieces of lumber to frame out the interior of the rough opening which makes for the proper thickness. I'd probably cut some 1/2 inch plywood to the necessary shape and glue three thicknesses of it together to gain the necessary thickness. The vent fan was designed to exhaust air from a small camper or van. The unit features a 100 CFM fan.
view full answer... - Does Spare Tire Affect Installation of Draw-Tite Trailer Hitch on 2016 Ram ProMaster City
- A full-size spare tire on your 2016 Ram ProMaster City will not affect the installation or fit whatsoever of the Draw-Tite Trailer Hitch Receiver # 75219.
The reason is the hitch gets installed behind the bumper cover, as you can see by the linked installation instructions. So the spare tire of your van is not going to be a hindrance or come into play during the install.
Along with the instructions I have also added a link to a video install for you to check out of the Draw-Tite Trailer...
view full answer... - Installation of Curt Trailer Hitch Receiver on 2016 Ram ProMaster City Wagon
- The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C13215 is a fit for the 2016 Ram ProMaster City Wagon. You will need to remove the tail lights, bumper cover, and bumper to install. I've attached the installation instructions to assist. The photos show the ProMaster City and not specifically the Wagon, but it is confirmed by the manufacturer to fit both.
view full answer... - Does T-One Vehicle Wiring Harness For 2018 Ram ProMaster City Need to Connect to Battery
- To ensure it works properly at all times, you will need to connect the hot lead directly to the battery of your 2018 Ram ProMaster City when you install the wiring harness that fits, which is the following part:
- T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118719
I have added a link below to an install of this harness on a similar model year ProMaster City which will detail the process for you.
view full answer... - Installation Instructions for Curt Hitch C13215 on a 2015 Ram ProMaster City Van
- Good news! I do have the installation instructions available for the Curt hitch # C13215 which is a confirmed fit for your 2015 Ram ProMaster City. We have not had the opportunity to install this hitch on a ProMaster City, but I took a look at the installation instructions and it looks very straight forward and there will be no drilling.
I have linked the instructions for the Curt hitch # C13215 to this page for your convenience.
view full answer... - Can Hot Lead From Wiring Harness be Run Inside Vehicle
- It sounds like you are referring to the hot lead for the Tekonsha T-One Vehicle Wiring Harness # 118719 that needs to be run up to the vehicle's battery. You can definitely route the wire inside your Ram ProMaster City as opposed to through the frame or underneath the vehicle.
Every vehicle is a bit different, so the particular path you will need to take when routing the wire in this manner will depend on the interior of your ProMaster City. Ideally you will be able to loosen or remove...
view full answer... - Can the Trailer Connector for the Curt Wiring Harness On a 2018 Ram ProMaster Be Routed Outside
- The Curt T-Connector Vehicle Wiring Harness part # C56270 which is a fit for a 2018 Ram ProMaster City can be installed so that the trailer connector is stored outside of the vehicle. In order to do so you will simply need to route the trailer connector through a grommet in the floor outside to the rear bumper. I don't have exact instructions on this but essentially you just need to peel up the carpet/panels near the rear bay access doors and then look for a grommet you can use to route...
view full answer... - How To Reverse Airflow Direction With A MaxxAir MAxxFan Plus RV Roof Vent
- On older models of RV roof vents you used to be able to just reverse the wiring to have the motor run in the reverse direction. With the current models of the MaxxAir MaxxFan, including the MaxxFan Plus Roof Vent w/ 12V Fan # MA00-04000K this feature is already programmed into the controller so that you don't have to change the wiring. Simply press the button (pictured below) to switch between pulling air in or out of the trailer.
These vents will come with mounting screws but do not...
view full answer... - Is There a Speed Limit for the Flint Hill Goods Hitch Mounted Aluminum Cargo Carrier
- The Flint Hill Goods Hitch Mounted Aluminum Cargo Carrier part # FHG59ZR doesn't have a speed rating so in all actuality, you can travel as fast as you want with the carrier attached. That said, I probably wouldn't use this at the track or during an off-road race but for all intents and purposes there is no speed rating/limit.
In regards to hitch mounted accessories like bike racks and cargo carrier, they typically aren't limited by speed.
view full answer... - Is It Normal for the Tekonsha Prodigy P3 # 90195 to Get Hot
- If you have the Tekonsha Prodigy P3 # 90195 installed properly and it is functioning normally, then it will be a bit hot after you are towing - especially if it was a bigger trailer. My contact at Tekonsha informed me that there is a metal aluminum plate on the bottom that actually works as a heatsink to keep it from overheating. It should cool down after the trailer is unplugged and it is not being used.
If it gets hot and you do not have a trailer connected or you have been parked for...
view full answer...
Go To Results